Yokogawa 2-Wire Dual Channel Transmitter/Analyzer FLXA21 - Manuel (Page 57)

Annexe 4 Tableau de réglage utilisateur DO
App.4-2
IM 12A01A02-12F-E
Paramètre
Valeurs par
défaut
Valeurs applicables Réglages
utilisateur *Réf.
Output
setup
mA Output Output, Simulate 16.3
Output Process parameter Oxygen1 Oxygen1, Tem-
perature1, Oxygen2,
Temperature2,
Calculated, Redun-
dant
Setup Linear Linear, Table
Linear 0 % value:
Oxygen
Temperature
0.00 mg/L,
ppm,
0.0 ppb, %SAT
0.0 ºC
mg/L, ppm:
0.00 à 50.00
ppb: 0.0 à 9999
%SAT: 0.0 à 600.0
ºC: -20.0 à 150.0
100 % value:
Oxygen
Temperature
20.00 mg/L,
ppm
100.0 ppb,
%SAT
50.0 ºC
Table — —
Burn Off Off, Low, High
Damping time 0.0 s 0.0 à 3600 s
Simulate Simulation perc. 50.00 % -2.5 à 112.5 %
Configure
Hold
Last or fixed Last Last, Fixed
Fixed value mA 12.00 mA 3.60 à 22.00 mA
Hold during Calibration(/Wash) Enabled Disabled, Enabled
Error
configura-
tion
DO too high Warn Off, Warn, Fail 16.4
DO too low Warn Off, Warn, Fail
Temperature too high Warn Off, Warn, Fail
Temperature too low Warn Off, Warn, Fail
Sensor membarane Off Off, Warn, Fail
Calib. time exceeded Off Off, Warn, Fail
Logbook
configura-
tion
Settings
logbook
Sensor: Error on 1-1 (2-1) Off, 1-1 (2-1), 1-2 (2-2) 16.5
Error off 1-1 (2-1) Off, 1-1 (2-1), 1-2 (2-2)
Zero low limit Off Off, 1-1 (2-1), 1-2 (2-2)
Zero high limit Off Off, 1-1 (2-1), 1-2 (2-2)
Slope low limit Off Off, 1-1 (2-1), 1-2 (2-2)
Slope high limit Off Off, 1-1 (2-1), 1-2 (2-2)
Stabilization time Off Off, 1-1 (2-1), 1-2 (2-2)
Pressure(meas.) Off Off, 1-1 (2-1), 1-2 (2-2)
Salinity comp. Off Off, 1-1 (2-1), 1-2 (2-2)
Wash setup Off Off, 1-1 (2-1), 1-2 (2-2)
mA: mA setup Off Off, 1-1 (2-1), 1-2 (2-2)
Hold fixed Value Off Off, 1-1 (2-1), 1-2 (2-2)
Burn Off Off, 1-1 (2-1), 1-2 (2-2)
Linear output % Off Off, 1-1 (2-1), 1-2 (2-2)
Damping time Off Off, 1-1 (2-1), 1-2 (2-2)
Erase logbook: 1-1 (2-1) 1-1 (2-1), 1-2 (2-2)
Erase? No No, Yes
Warn if logbook “full”: No No, Yes