Yokogawa 2-Wire Dual Channel Transmitter/Analyzer FLXA21 - Manuel (Page 53)

Annexe 3 Tableau de réglage utilisateur ISC
App.3-2
IM 12A01A02-12F-E
Paramètre
Valeurs par
défaut
Valeurs applicables Réglage
utilisateur
*Réf.
.
Output
setup
mA Output Output, Simulate 13.2
Output Process parameter Conduct1-
TC1,
(Concent1-
TC1)
Conduct1-TC1,
Temperature1,
Conduct1-TC2,
Concent1-TC1,
Concent1-TC2
Setup Linear Linear, Table
Linear 0 % value
Conductivity
Temperature
Concentration
0.000 µS/cm,
mS/m
0.0 ºC
0.000 %,
ppm, ppb,
0 ppt
0.000 à 5.000 S/cm,
0.000 à 500.0 S/m
-20 à 140 ºC
0.000 а 999.9 %,
0.000 а 9999 ppm,
ppb, 0 à 9999 ppt
100 % value
Conductivity
Temperature
Concentration
1.000 S/cm,
100.0 S/m
100 ºC
100.0 %,
9999 ppm,
ppb, ppt
0 à 5.000 S/cm, 0 à
500.0 S/m
-20 à 140 ºC
0.000 а 999.9 %,
0.000 а 9999 ppm,
ppb, 0 à 9999 ppt
Table — —
Burn Off Off, Low, High
Damping time 0.0 s 0.0 à 3600 s
Simulate Simulation perc. 50.00 % -2.5 à 112.5 %
Configure
Hold
Last or fixed Last Last, Fixed
Fixed value mA 12.00 mA 3.60 à 22.00 mA
Hold during Calibration Enabled Disabled, Enabled
Error
configura-
tion
Conductivity too high (or Concentration) Warn Off, Warn, Fail 13.3
High limit 1.000 S 0.00 nS à 500.0 S
Conductivity too low (or Concentration) Warn Off, Warn, Fail
Low limit 5.000 µS 0.000 nS à 500.0 S
Temperature too high Warn Off, Warn, Fail
Temperature too low Warn Off, Warn, Fail
Calibr.time exceeded Off Off, Warn, Fail
Configura-
tion error:
1st comp. matrix Fail Off, Warn, Fail
2nd comp. matrix Fail Off, Warn, Fail
Concentration table Fail Off, Warn, Fail
Logbook
configura-
tion
Settings
logbook
Sensor: Error on 1-1 Off, 1-1, 1-2 13.4
Error off 1-1 Off, 1-1, 1-2
Temp.coeff. Off Off, 1-1, 1-2
Air adjust limit Off Off, 1-1, 1-2
Adj c.c.low limit Off Off, 1-1, 1-2
Adj c.c.high limit Off Off, 1-1, 1-2
Reference temp. Off Off, 1-1, 1-2
Stabilization time Off Off, 1-1, 1-2
mA: mA setup Off Off, 1-1, 1-2
Hold fixed Value Off Off, 1-1, 1-2
Burn Off Off, 1-1, 1-2
Linear output % Off Off, 1-1, 1-2
Damping time Off Off, 1-1, 1-2
Erase logbook: 1-1 1-1, 1-2
Erase? No No, Yes
Warn if logbook “full”: No No, Yes