GE Zoneline Internal Condensate Removal 14,300 BTU Packaged Terminal Air Conditioner User Manual - Manuel (Page 18)

49-7774
Installation Instructions
INST
ALLA
TION INSTRUCTIONS
Use the correct wall case
7KLVXQLW is designed to be installed in a GE
$SSOLDQFHVSODVWLFRULQVXODWHGPHWDOZDOOFDVH7KLV
minimizes condensation from forming on the room side
of the case.
NOTE: 7KHUHDUHVHYHUDOH[WUDKROHVLQWKHXQLWVLGH
flanges for installation in wall cases other than GE
$SSOLDQFHV7RDYRLGGDPDJLQJWKHIODQJHLQVXODWLRQ
the installer should use an awl or other sharp tool to
puncture the insulation in the appropriate holes before
installing the attachment screws.
Use the correct outdoor grille
You should use the outdoor grilles shown on the
³(VVHQWLDO(OHPHQWV´ODEHORQWKHEDVHSDQ
• ,IDQH[LVWLQJJULOOHLVQRWUHSODFHGFDSDFLW\DQG
efficiency will be reduced and the unit may fail to
operate properly or fail prematurely. A deflector
NLW5$.PD\EHXVHGZLWKJULOOHVWKDWZHUHQRW
GHVLJQHGIRU\RXUQHZ*($SSOLDQFHV=RQHOLQHV
7KH5$.FRQWDLQVDLUGHIOHFWRUVDQGJDVNHWV
WKDWPRXQWWRWKHXQLWWRGLUHFWWKHKRWH[KDXVWDLU
away from the air intake to allow the unit to function
properly
. The grille must have a 65% minimum
free area (as calculated by ASHRAE). See the
Architects and Engineers Data Manual for more
detailed information.
• Any vertical deflectors in a non GE Appliances
H[LVWLQJUHDUJULOOHVKRXOGEHUHPRYHGWRGHFUHDVH
condenser air recirculation that can cause the unit
WR³VKRUWF\FOH´DQGOHDGWRSUHPDWXUHFRPSRQHQW
failure.
Use the correct power cord
/RFDOFRGHVPD\UHTXLUHWKHXVHRIDUFIDXOWRU
OHDNDJHFXUUHQWGHWHFWLRQGHYLFHVRQYROW
installations.
Replacing a ducted unit
New ducted installation:
,IWKLVXQLWLVWREHLQVWDOOHGLQDQHZGXFWHGDSSOLFDWLRQ
using a duct adapter kit, the kit must be installed before
WKHXQLWLVSODFHGLQWKHZDOOFDVH7KHLQVWDOODWLRQ
instructions are packed with the kit.
Duct kits available:
5$.
5$.%%
Existing ducted installation:
5HSODFHPHQWRIDQH[LVWLQJGXFWHGXQLWPD\UHTXLUH
different components. Request this information from
your sales representative.
Duct seals on existing
unit need to be removed and added to the new
unit.
• Replacing 230/208 volt units:
6HHSDJH
• Replacing 265 volt units:
6HHSDJH
When using a duct kit, you must always turn Mode
7 to ON “ ”
6HH0RGHLQVWUXFWLRQVRQSDJH
REPLACING AN EXISTING UNIT
Check the “Essential
(OHPHQWV´ODEHOIRU
important information.
Duct
Case
Mounting
plate
Duct Mode
Shown ON