Pioneer VSX-C501-S - Manuel (Page 41)

The System Setup menu
41
En
English
09
Volume control setting
When the Volume Control setting is switched off it is
necessary to turn up the volume on the plasma display.
• VOL C.OFF – The receiver does not control the
volume of the plasma display
• VOL C.ON – When the receiver is switched to an
input that used the plasma display (DVD, for
example), the volume on the plasma display is muted
so only sound from the receiver is heard.
Function setting for DVD input
• DVD: 1 – 5, TV (default: 3) – Matches the DVD
function of the receiver with a numbered video input
on the plasma display. For example,
DVD: 3 matches
the DVD input with AV 3 on the plasma display (see
also Using this receiver with a Pioneer plasma display
on page 19).
Function setting for STB input
• STB: 1 – 5, TV (default: 1) – Matches the STB
function of the receiver with a numbered video input
on the plasma display. For example,
STB: 1 matches
the STB input with AV 1 on the plasma display (see
also Using this receiver with a Pioneer plasma display
on page 19).
Function setting for DVR/TV input
• DVR: 1 – 5, TV (default: 2) – Matches the DVR/TV
function of the receiver with a numbered video input
on the plasma display. For example,
DVR: 2 matches
the DVR/TV input with AV 2 on the plasma display
(see also Using this receiver with a Pioneer plasma
display on page 19).
Function setting for VIDEO input
• VIDEO 1 – 5, TV (default: TV) – Matches the VIDEO
function of the receiver with a numbered video input
on the plasma display. For example,
VIDEO: TV
matches the VIDEO input with TV on the plasma
display (see also Using this receiver with a Pioneer
plasma display on page 19).
Function setting for FRONT input
• FRONT 1 – 5, TV (default: 4) – Matches the FRONT
function of the receiver with a numbered video input
on the plasma display. For example,
FRONT: 4
matches the FRONT input with AV 4 on the plasma
display (see also Using this receiver with a Pioneer
plasma display on page 19).
Note
• When adjusting the volume, the volume display
shown on-screen on the plasma display and the
volume displayed in the front panel display of the
receiver may be different. The plasma display volume
indication is only approximate.
Setting individual channel levels
Use to set the relative volume of each channel as you find
necessary for balanced surround sound.
1 Use MASTER VOLUME to adjust the volume to an
appropriate level.
2 Press TEST TONE to output the test tone.
The test tone is output in the following order (from
speakers that are switched on and are appropriate for the
current listening mode):
• L – Front left
• C – Center
• R – Front right
• RS – Right surround
• SB – Surround back
• LS – Left surround
• SW – Subwoofer
3 Use the LEVEL +/– buttons to adjust speaker
levels so that you hear the test tone at the same
volume from each speaker when seated in your main
listening position.
• The channel level range is ± 10 dB.
4 Press TEST TONE to turn off the test tone.
Note
• Since the subwoofer transmits an ultra-low
frequency its sound may seem quieter than it actually
is. Be careful not to turn up your subwoofer too much
and check the volume with an actual source.
• The subwoofer volume is best controlled with the
volume control on the subwoofer unit itself.
• The speaker volume can be adjusted without
outputting the test tone by pressing CH SELECT then
using the LEVEL +/– buttons. This level setting mode
is automatically exited after 5 seconds of inactivity.
• The default setting is 0 dB for all channels.
• You cannot use the test tone when the multichannel
analog inputs ( DVD 5.1ch) are selected, or when
playing 88.2/96 kHz PCM or 96/24 DTS sources.
SOURCE RECEIVER
SLEEP
RECEIVER
AV DIRECT
INPUT
DVD
VIDEO
STB
FRONT FM/AM
DVR/TV
SURROUND
ADVANCED
SURROUND
SOUND MODE DIALOG
AUTO STEREO
LEVEL TEST TONE CH SELECT
MUTE
MASTER
VOLUME
DTV MENU
TOP MENU T.EDIT
MENU
ROOM
SETUP
TUNE
ST ST
SYSTEM SETUP
ENTER
vsx-c501(WY).book 41 ページ ２００３年５月２２日 木曜日 午前１０時２９分