STI 1210 - Manuel

Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
INSTALLATION OF STI-1210A SPEAKER HORN/STROBE DAMAGE STOPPER®
All specifications and information shown were current as of publication and are subject to change without notice.
FOR CONDUIT INSTALLATION (NOT INCLUDED)
“A” Rain-tight hub with neoprene o-ring threaded for
3/4 in. NPT rigid conduit
“B” 3/4 in. female adapter
“C” 3/4 in. - 1/2 in. reducing bushing
“D” Galvanized 1/2 x 1 in. conduit nipple
“E” 1/2 in. conduit lock nut
“F” 4 in. square backbox
“G” 4 in. square box extension (optional). Use to
extend strobe into cover area
INSTALLATION NOTES
1. To minimize strobe light loss, regardless of the type of horn/strobe appliance used, the clear section
(not the section containing the cutout slots) must be centered over the strobe light lens. Failure to
follow these instructions may lead to light loss transmission.
2. Damage Stopper must be installed to comply with applicable NEC, NFPA and local codes.
3. In areas where frequent wash downs occur, standoff blocks must be used.
4. Damage Stopper may be installed outdoors when appliance carries an outdoor rating.
Electronic warranty form at www.sti-usa.com/wc14
1210AIS MAY07
CLEANING INSTRUCTIONS
Rinse with water to remove abrasive dust and dirt. Wash with
soap or mild detergent, using a soft cloth (do not scrub). Rinse
once more then dry with a soft cloth or chamois. To remove
grease or wet paint, rub gently with a cloth wetted with
naphtha. Then wash and rinse. DO NOT USE RAZOR BLADES. (DO
NOT USE RAZOR BLADES.) INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW
1. Insert the (4) 06297T external mounting tabs into the frame assembly slots.
2. Using backbox assembly as a template, place against mounting surface at proper location according to NFPA 72.
3. Mark and drill (4) holes 1/4 in. (6.3mm) diameter, 1 1/4 in. (32mm) deep.
4. Insert the (4) anchors into the wall.
5. Mount backbox to wall with screws.
6. Install electrical fittings as needed.
7. Install horn/strobe appliance.
8. Install cover with clips and screws.
9. Test appliance according to appliance manufacturer’s instructions.
1
2
B
C
D
F
E
G
HORIZONTAL CENTERLINE
OF ENCLOSURE
CENTERLINE
MOUNTING BOSS
FOR BACKBOX MOUNTING
HEIGHT 80 in.
FRONT VIEW OF ENCLOSURE
A 1-1/16 in. DIAMETER CONDUIT
ENTRY HOLE MUST BE FIELD INSTALLED
CENTER LINE
TOP VIEW
1-3/4
TOP VIEW
A 1-1/16 in.
DIAMETER CONDUIT
ENTRY HOLE MUST
BE FIELD INSTALLED
CENTER LINE
1-3/4
#8-32 x 3/8 in.
MACHINE SCREWS
(NOT INCLUDED)
DRILL FOR CONDUIT ENTRY
CLEAR
SECTION
HEIGHT
7.75 in.(197mm)
WIDTH
5.25 in.(133mm)
DEPTH
6.5 in.(165mm)
629764 RETAINING CLIPS
(4) PROVIDED
629761 NEOPRENE GASKET
629762
DRAIN
SCREEN
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
A
06297T MOUNTING
TABS (4) PROVIDED
!
06297A BACKBOX
NEOPRENE GASKET
3 3/8 in.
(86mm)
3/4 in.(44mm)
629763 STANDOFF BLOCKS
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREWS
(4) PROVIDED
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
1
2
B
C
D
F
E
G
HORIZONTAL CENTERLINE
OF ENCLOSURE
CENTERLINE
MOUNTING BOSS
FOR BACKBOX
MOUNTING
HEIGHT 80 in.
FRONT VIEW OF ENCLOSURE
A 1-1/16 in. DIAMETER CONDUIT
ENTRY HOLE MUST BE FIELD INSTALLED
CENTER LINE
TOP VIEW
1-3/4
TOP VIEW
A 1-1/16 in.
DIAMETER CONDUIT
ENTRY HOLE MUST
BE FIELD INSTALLED
CENTER LINE
1-3/4
#8-32 x 3/8 in.
MACHINE SCREWS
(NOT INCLUDED)
DRILL FOR CONDUIT ENTRY
CLEAR
SECTION
HEIGHT
7.75 in.(197mm)
WIDTH
5.25 in.(133mm)
DEPTH
6.5 in.(165mm)
629764 RETAINING CLIPS
(4) PROVIDED
629761 NEOPRENE GASKET
629762
DRAIN
SCREEN
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
A
06297T MOUNTING
TABS (4) PROVIDED
!
06297A BACKBOX
NEOPRENE GASKET
3 3/8 in.
(86mm)
3/4 in.(44mm)
629763 STANDOFF BLOCKS
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREWS
(4) PROVIDED
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
1
2
B
C
D
F
E
G
HORIZONTAL CENTERLINE
OF ENCLOSURE
CENTERLINE
MOUNTING BOSS
FOR BACKBOX MOUNTING
HEIGHT 80 in.
FRONT VIEW OF ENCLOSURE
A 1-1/16 in. DIAMETER CONDUIT
ENTRY HOLE MUST BE FIELD INSTALLED
CENTER LINE
TOP VIEW
1-3/4
TOP VIEW
A 1-1/16 in.
DIAMETER CONDUIT
ENTRY HOLE MUST
BE FIELD INSTALLED
CENTER LINE
1-3/4
#8-32 x 3/8 in.
MACHINE SCREWS
(NOT INCLUDED)
DRILL FOR CONDUIT ENTRY
CLEAR
SECTION
HEIGHT
7.75 in.(197mm)
WIDTH
5.25 in.(133mm)
DEPTH
6.5 in.(165mm)
629764 RETAINING CLIPS
(4) PROVIDED
629761 NEOPRENE GASKET
629762
DRAIN
SCREEN
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
A
06297T MOUNTING
TABS (4) PROVIDED
!
06297A BACKBOX
NEOPRENE GASKET
3 3/8 in.
(86mm)
3/4 in.(44mm)
629763 STANDOFF BLOCKS
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREWS
(4) PROVIDED
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
1
2
B
C
D
F
E
G
HORIZONTAL CENTERLINE
OF ENCLOSURE
CENTERLINE
MOUNTING BOSS
FOR BACKBOX
MOUNTING
HEIGHT 80 in.
FRONT VIEW OF ENCLOSURE
A 1-1/16 in. DIAMETER CONDUIT
ENTRY HOLE MUST BE FIELD INSTALLED
CENTER LINE
TOP VIEW
1-3/4
TOP VIEW
A 1-1/16 in.
DIAMETER CONDUIT
ENTRY HOLE MUST
BE FIELD INSTALLED
CENTER LINE
1-3/4
#8-32 x 3/8 in.
MACHINE SCREWS
(NOT INCLUDED)
DRILL FOR CONDUIT ENTRY
CLEAR
SECTION
HEIGHT
7.75 in.(197mm)
WIDTH
5.25 in.(133mm)
DEPTH
6.5 in.(165mm)
629764 RETAINING CLIPS
(4) PROVIDED
629761 NEOPRENE GASKET
629762
DRAIN
SCREEN
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
A
06297T MOUNTING
TABS (4) PROVIDED
!
06297A BACKBOX
NEOPRENE GASKET
3 3/8 in.
(86mm)
3/4 in.(44mm)
629763 STANDOFF BLOCKS
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREWS
(4) PROVIDED
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
INTERNAL DIMENSIONS
INSTALL CLAMP IN NOTCH 2 AS SHOWN REMARQUES SUR L’INSTALLATION
1. Afin de minimiser la perte de lumière stroboscopique, quel que soit le type d’alarme sonore/de stroboscope utilisé, la section
dégagée (et NON la section contenant les fentes de découpe), doit être centrée sur l’objectif stroboscopique. Le fait d’omettre
ces instructions risque d’entraîner la perte de diffusion de la lumière.
2. Le Stopper de dégâts doit être installé de sorte à être conforme avec les normes NEC, NFPA applicables et les codes locaux.
3. Dans les zones où des jets d’eau fréquents surviennent, des blocs de détection à distance doivent être utilisés.
4. Il est possible d’installer un Stopper de dégâts à l’extérieur lorsque l’appareil est homologué pour utilisation à l’extérieur.