STI 1221 - Manuel

Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
INSTALLATION OF STI-1221C STROBE DAMAGE STOPPER ®
All specifications and information shown were current as of publication and are subject to change without notice.
INSTALLATION NOTES
1. To minimize strobe light loss, regardless of the type of strobe
appliance used, center cover over the strobe light lens. Failure to
follow these instructions may lead to light loss transmission.
2. Damage Stopper must be installed to comply with applicable
NEC, NFPA and local codes.
3. In applications where wash downs, rainfall or condensation
occur, it is recommended that a drain or weep hole be provided.
Refer to weep hole installation diagram.
4. Damage Stopper may be installed outdoors when appliance
carries an outdoor rating.
Electronic warranty form at www.sti-usa.com/wc14
1221CIS APRIL2006
CLEANING INSTRUCTIONS
Rinse with water to remove
abrasive dust and dirt. Wash with
soap or mild detergent, using a
soft cloth (do not scrub). Rinse
once more then dry with a soft
cloth or chamois. To remove
grease or wet paint, rub gently
with a cloth wetted with naphtha.
Then wash and rinse.
DO NOT USE RAZOR BLADES.
INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW
1. Insert the (4) 06297T external mounting tabs into the frame
assembly slots.
2. Using back box assembly as a template, place against
mounting surface at proper location according to NFPA 72.
3. Mark and drill (4) holes 1/4 in. (6.3mm) diameter, 1 1/4 in.
(32mm) deep.
4. Insert the (4) anchors into the wall.
5. Mount back box to wall with screws.
6. Install electrical fittings as needed.
7. Install strobe appliance.
8. Install cover with clips and screws.
9. Test appliance according to appliance manufacturer’s
instructions.
629764 CLAMP
(4) PROVIDED
APPROX
CENTER LINE
OF UNDERSIDE OF
COVER
1 in.(25mm)
1
2
19033 ANCHOR
(4) PROVIDED
EXISTING
HORN/STROBE
APPLIANCE
OPTIONAL CONDUIT HUB
SUB-6297B20
(ACCEPTS 3/4 in. RIGID
CONDUIT FITTINGS)
INCLUDES GASKET AND
MOUNTING HARDWARE
LOCATED IN THIS AREA
DRILL A 1/4 in.(6.3mm) DIA. HOLE
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS OREDER SUB-122
ENVIRO KIT
06297T EXTERNAL
MOUNTING TABS —
INSERT TABS INTO
FRAME SLOTS AS SHOWN
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREW (4) PROVIDED 06297C FRAME ASSY.
DEPTH
4.75 in.(120mm)
WIDTH
5.25 in.(133mm)
HEIGHT
7.75 in.(197mm)
01221 COVER ONLY
!
01221 COUVERCLE SEULEMENT
INSTALL CLAMP IN 2nd NOTCH AS SHOWN
629764 CLAMP
(4) PROVIDED
APPROX
CENTER LINE
OF UNDERSIDE OF
COVER
1 in.(25mm)
1
2
19033 ANCHOR
(4) PROVIDED
EXISTING
HORN/STROBE
APPLIANCE
OPTIONAL CONDUIT HUB
SUB-6297B20
(ACCEPTS 3/4 in. RIGID
CONDUIT FITTINGS)
INCLUDES GASKET AND
MOUNTING HARDWARE
LOCATED IN THIS AREA
DRILL A 1/4 in.(6.3mm) DIA. HOLE
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS OREDER SUB-122
ENVIRO KIT
06297T EXTERNAL
MOUNTING TABS —
INSERT TABS INTO
FRAME SLOTS AS SHOWN
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREW (4) PROVIDED 06297C FRAME ASSY.
DEPTH
4.75 in.(120mm)
WIDTH
5.25 in.(133mm)
HEIGHT
7.75 in.(197mm)
01221 COVER ONLY
!
01221 COUVERCLE SEULEMENT INTERNAL DIMENSIONS
WEEP HOLE INSTALLATION
REMARQUES SUR L’INSTALLATION
1. Afin de minimiser la perte de lumière stroboscopique, quel que soit le type de
stroboscope utilisé, le couvercle doit être centré sur l’objectif stroboscopique. Le
fait d’omettre ces instructions risque d’entraîner la perte de diffusion de la lumière.
2. Le Stopper de dégâts doit être installé de sorte à être conforme avec les normes
NEC, NFPA applicables et les codes locaux.
3. Dans les applications où des jets d’eau, des précipitations ou de la condensation se
produisent, il est recommandé de prévoir un trou de vidange ou une barbacane.
Reportez-vous à schéma d’installation d’une barbacane.
4. Il est possible d’installer un Stopper de dégâts à l’extérieur lorsque l’appareil est
homologué pour utilisation à l’extérieur.