STI 1229 - Manuel

Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
INSTALLATION OF STI-1229 STOPPER ® DOME FOR STROBE
All specifications and information shown were current as of publication and are subject to change without notice.
INSTALLATION NOTES
1. To minimize strobe light loss, regardless of the type of strobe
appliance used, the clear section must be centered over the
strobe light lens. Failure to follow these instructions may lead to
light loss transmission.
2. Stopper Dome must be installed to comply with applicable NEC,
NFPA and local codes.
3. Stopper Dome may be installed outdoors when appliance carries
an outdoor rating.
4. If added protection is needed due to environmental conditions,
order SUB-123 Enviro kit.
Electronic warranty form at www.sti-usa.com/wc14
1229IS APRIL2006
CLEANING INSTRUCTIONS
Rinse with water to remove abrasive dust and dirt. Wash
with soap or mild detergent, using a soft cloth (do not
scrub). Rinse once more then dry with a soft cloth or
chamois. To remove grease or wet paint, rub gently with a
cloth wetted with naphtha. Then wash and rinse.
DO NOT USE RAZOR BLADES. INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW
1. Using cover as a template, place against mounting surface at proper
location according to NFPA 72.
2. Mark and drill (6) holes 3/16 in. (4.7mm) diameter, 1 in. (25mm) deep.
3. Insert the (6) anchors into the wall.
4. Install strobe appliance.
5. Install cover with washers and screws.
6. Test appliance according to appliance manufacturer’s instructions.
NEMA 4X CONDUIT HUB
(NOT PROVIDED)
NOTE: ACCESS HOLE MUST BE FIELD
DRILLED TO APPROPRIATE SIZE
HOLE MUST BE DRILLED
AS SHOWN, CENTERED ON
UPPER OR LOWER FLAT
SURFACE
01222 ENCLOSED SPACER
(1) PROVIDED
01289 APPLIANCE MOUNTING PLATE
(1) PROVIDED
19051 PHILLIPS FLAT HEAD SCREW
#8-32 x 3/8 in.
(4) PROVIDED
EXISTING HORN/STROBE APPLIANCE
070498N GASKET
(1) PROVIDED
01225 COVER
(1) PROVIDED
19049 WASHER
(6) PROVIDED
19050 #8-32 x 3/4 in.
SOCKET HEAD CAP SCREW
(6) PROVIDED
19013 SCREW #10 x 1 1/2 in.
(4) PROVIDED
10933 ANCHOR
(4) PROVIDED
DRILL (4) 1/4 in.(6.3mm)
DIA. HOLES
IN AREAS WHERE
FREQUENT WASHDOWNS
OCCUR WASHERS MAY BE
USED TO STAND OFF ENCLOSED SPACER
NOT PROVIDED
9.37 in.(238mm)
2.87 in.(73mm)
4.25 in.
(108mm)
01289 APPLIANCE
MOUNTING PLATE
PRODUCT DIMENSIONS
NEMA 4X CONDUIT HUB
(NOT PROVIDED)
NOTE: ACCESS HOLE MUST BE FIELD
DRILLED TO APPROPRIATE SIZE
HOLE MUST BE DRILLED
AS SHOWN, CENTERED ON
UPPER OR LOWER FLAT
SURFACE
01222 ENCLOSED SPACER
(1) PROVIDED
01289 APPLIANCE MOUNTING PLATE
(1) PROVIDED
19051 PHILLIPS FLAT HEAD SCREW
#8-32 x 3/8 in.
(4) PROVIDED
EXISTING HORN/STROBE APPLIANCE
070498N GASKET
(1) PROVIDED
01225 COVER
(1) PROVIDED
19049 WASHER
(6) PROVIDED
19050 #8-32 x 3/4 in.
SOCKET HEAD CAP SCREW
(6) PROVIDED
19013 SCREW #10 x 1 1/2 in.
(4) PROVIDED
10933 ANCHOR
(4) PROVIDED
DRILL (4) 1/4 in.(6.3mm)
DIA. HOLES
IN AREAS WHERE
FREQUENT WASHDOWNS
OCCUR WASHERS MAY BE
USED TO STAND OFF ENCLOSED SPACER
NOT PROVIDED
9.37 in.(238mm)
2.87 in.(73mm)
4.25 in.
(108mm)
01289 APPLIANCE
MOUNTING PLATE
PRODUCT DIMENSIONS