STI 1227 - Manuel

Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
INSTALLATION OF STI-1227 STOPPER ® DOME FOR STROBE
All specifications and information shown were current as of publication and are subject to change without notice.
INSTALLATION NOTES
1. To minimize strobe light loss, regardless of the type of strobe appliance used, the clear
section must be centered over the strobe light lens. Failure to follow these instructions
may lead to light loss transmission.
2. Stopper Dome must be installed to comply with applicable NEC, NFPA and local codes.
3. Stopper Dome may be installed outdoors when appliance carries an outdoor rating.
4. If added protection is needed due to environmental conditions, order SUB-123 Enviro kit.
Electronic warranty form at www.sti-usa.com/wc14
1227IS APRIL2006
CLEANING INSTRUCTIONS
Rinse with water to remove abrasive dust and dirt. Wash with soap or mild
detergent, using a soft cloth (do not scrub). Rinse once more then dry with a soft
cloth or chamois. To remove grease or wet paint, rub gently with a cloth wetted
with naphtha. Then wash and rinse.
DO NOT USE RAZOR BLADES.
INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW
1. Using cover as a template, place against mounting surface at proper location
according to NFPA 72.
2. Mark and drill (6) holes 3/16 in. (4.7mm) diameter, 1 in. (25mm) deep.
3. Insert the (6) anchors into the wall.
4. Install strobe appliance.
5. Install cover with washers and screws.
6. Test appliance according to appliance manufacturer’s instructions.
2.87 in.(73mm)
7.87 in.(200mm)
1.62 in.(41mm)
7.37 in.(187mm)
STI-1215
COVER
STI-1212
SPACER
PLASTIC INSERT
(1) PROVIDED CONDUIT SEALING GASKET
SUB-123 ENVIRO KIT
ADHESIVE BACKED GASKET
SPACER TO MOUNTING SURFACE
EXISTING
WARNING
APPLIANCE
19033 ANCHOR
(4) PROVIDED
01212 SPACER
19013 SCREW
#10 x 1-1/2 in.
(4) PROVIDED
GASKET
(COVER TO SPACER)
01215 HORN/STROBE
PROTECTIVE COVER
19049 WASHER (6) PROVIDED
19047 #8 - 32 x 3/8 in.
SOCKET HEAD CAP SCREW
(6) PROVIDED
IF ADDED PROTECTION IS NEEDED
DUE TO ENVIROMENTAL CONDITIONS
ORDER SUB-123 ENVIRO KIT
ALSO INCLUDES (6)
#8-32 X 3/4 in. SOCKET CAP SCREWS
PLASTIC INSERT
(1) PROVIDED
CONDUIT SEALING GASKET
SUB-123 ENVIRO KIT
ADHESIVE BACKED GASKET
SPACER TO MOUNTING SURFACE
EXISTING
WARNING
APPLIANCE
01212 SPACER
19013 SCREW
#10 x 1-1/2 in.
(4) PROVIDED
GASKET
(COVER TO SPACER)
01225 STROBE
PROTECTIVE COVER
19049 WASHER (6) PROVIDED
19047 #8 - 32 x 3/8 in.
SOCKET HEAD CAP SCREW
(6) PROVIDED
19033 ANCHOR
(4) PROVIDED
IF ADDED PROTECTION IS NEEDED
DUE TO ENVIROMENTAL CONDITIONS
ORDER SUB-123 ENVIRO KIT
ALSO INCLUDES (6)
#8-32 X 3/4 in. SOCKET CAP SCREWS
2.87 in.(73mm)
7.87 in.(200mm)
1.62 in.(41mm)
7.37 in.(187mm)
STI-1215
COVER
STI-1212
SPACER
PRODUCT DIMENSIONS
REMARQUES SUR L’INSTALLATION
1. Afin de minimiser la perte de lumière stroboscopique, quel que soit le type de stroboscope
utilisé, le couvercle doit être centré sur l’objectif stroboscopique. Le fait d’omettre ces
instructions risque d’entraîner la perte de diffusion de la lumière.
2. Le dôme Stopper doit être installé de sorte à être conforme avec les normes NEC, NFPA
applicables et les codes locaux.
3. Il est possible d’installer un dôme Stopper à l’extérieur lorsque l’appareil est homologué
pour utilisation à l’extérieur.
4. S’il est nécessaire d’ajouter une autre protection en raison des conditions
environnementales, commandez la trousse Enviro, SUB-123.