Edwards Signaling 1508 - Manuel

Installation Instructions for Surface Wall Mount Electromagnetic Door
Holders Catalog Series 1508
P/N 3100538 ISSUE 1 © 2003
501-152700-0-01
Description
The 1508 Series are surface wall mount door holders for use with
single doors. All are UL and cUL Listed and FM approved.
Installation
Install and wire in accordance with applicable codes, standards,
such as NFPA publications 70 (National Electrical Code), 72 (Na-
tional Fire Alarm Code), and 80 (Standard for Fire Doors and Fire
Windows), and/or other regulations applicable to the country
and locality of installation and in accordance with authorities
having jurisdiction.
Table 1. Specifications
Cat. No. Volts Amps
1508-E1 12V DC 0.170
1508-E5 12V AC 60 Hz 0.150
1508-AQN5 24V AC 60 Hz 0.015
24V DC 0.015
120V AC 60 Hz 0.015
1. Using Figure 1 and Table 2, locate the intersection of
Dimension X and Dimension Y. Dimension Z is shown at the
intersection in the gray area.
NOTE: If dimension X or Y is not shown on the chart,
extrapolate Dimension Z. (i.e., if X=7, and Y=30, Z
= (27-5/8 - ((27-5/8 - 27-1/4)/2)) => Z = 27-9/16" )
2. Mount the surface housing (supplied) vertically on the
horizontal center line and 5" from the top of the door with
two 1/4-20 x 1" screws (provided).
NOTE: The outlet box must be able to withstand a maximum
holding force of 50 pounds.
If X and Y intersect in the blank area in Table 2, DO NOT
install the outlet box. The contact plate and electromagnet
cannot be aligned with these dimensions.
Door
Door jamb
Wall line
Outlet box
center
line
X
Z Y
Figure 1. Locating the Door Holder
Table 2. Dimension chart (in inches (mm))
Electromagnet Assembly Mounting
1. Refer to Figure 4. If not using surface metal raceway (not
supplied), secure the acrylic insulating sleeve (provided) to
the hole in the surface housing with the #8-32 x 3/16" screw
provided.
WARNING
To prevent electrical shock, ensure power is discon-
nected.
2. Pull field wiring through conduit into the surface housing. If
surface metal raceway (not supplied) is being used, the
required size is 1/2" wide x 11/32" high. The raceway will
seat 1/4" into the surface housing. Wiring should be run
through the acrylic insulating sleeve where applicable.
3. Establish earth-ground continuity in accordance with
applicable codes, standards and authorities having
jurisdiction.
4. For -E1 and -E5 models, connect the field power wiring to the
electromagnet assembly wiring leads.
For -AQN5 models, refer to Figure 2 and connect as
instructed below:
a. 120V AC operation. Connect power field wiring to
terminals marked "120V AC" and "COM."
b. 24V AC/DC operation. Connect power field wiring to
terminals marked "24V AC/DC" and "COM."
CHESHIRE, CT 203-699-3300 CUST. SERV. FAX 203-699-3365 TECH SERV. FAX 203-699-3078
28 30 32 34 36 38 40 42 44 46 48
2 26 (660) 28 (711) 29 7/8 (759) 32 (813) 34 (864) 36 (914) 38 (965) 40 (1016) 42 (1067) 43 7/8 (1114) 45 5/8 (1159)
4 26 (660) 28 (711) 29 7/8 (759) 32 (813) 34 (864) 36 (914) 38 (965) 40 (1016) 42 (1067) 43 7/8 (1114) 45 5/8 (1159)
6 25 5/8 (651) 27 5/8 (702) 29 5/8 (752) 31 3/4 (806) 33 3/4 (857) 35 3/4 (908) 37 3/4 (959) 39 3/4 (1010) 41 3/4 (1060) 43 5/8 (1108) 45 3/8 (1153)
8 25 1/4 (641) 27 1/4 (692) 29 1/4 (743) 31 3/8 (797) 33 1/2 (851) 35 1/2 (902) 37 3/8 (949) 39 1/2 (1003) 41 1/2 (1054) 43 3/8 (1102) 45 1/4 (1149)
10 24 5/8 (625) 26 3/4 (679) 28 3/4 (730) 30 7/8 (784) 33 (838) 35 (889) 37 (940) 39 1/8 (994) 41 1/8 (1045) 43 (1092) 44 7/8 (1140)
12 23 3/4 (603) 25 7/8 (657) 28 (711) 30 1/8 (765) 32 1/4 (819) 34 3/8 (873) 36 3/8 (924) 38 1/2 (978) 40 5/8 (1032) 42 1/2 (1080) 44 3/8 (1127)
14 23 3/4 (603) 25 (635) 27 1/4 (692) 29 3/8 (746) 31 1/2 (800) 33 3/4 (857) 35 7/8 (911) 38 (965) 40 (1016) 42 (1067) 43 7/8 (1114)
16 21 3/4 (552) 24 (610) 26 1/4 (667) 28 1/2 (724) 30 3/4 (781) 33 (838) 35 1/8 (892) 37 1/4 (946) 39 3/8 (1000) 41 3/8 (1051) 43 3/8 (1102)
18 20 (508) 22 1/2 (572) 25 (635) 27 3/8 (695) 29 3/4 (756) 32 (813) 34 1/4 (870) 36 1/2 (927) 38 5/8 (981) 40 5/8 (1032) 42 1/2 (1080)
20 18 1/4 (463) 21 (533) 23 1/2 (597) 26 (660) 28 1/2 (724) 30 7/8 (784) 33 1/8 (841) 35 3/8 (899) 37 5/8 (956) 39 5/8 (1006) 41 5/8 (1057)
22 18 3/4 (476) 21 5/8 (549) 24 3/8 (619) 27 (686) 29 3/8 (746) 31 3/4 (806) 34 1/8 (867) 36 1/2 (927) 38 5/8 (981) 40 3/4 (1035)
24 22 1/2 (572) 25 1/2 (648) 28 1/8 (714) 30 5/8 (778) 33 1/8 (841) 35 5/8 (905) 37 7/8 (962) 40 (1016)
26 Do not install outlet box if 26 1/4 (667) 29 (737) 31 5/8 (803) 34 1/4 (870) 36 1/2 (927) 38 5/8 (981)
28 Dimensions X and Y intersect in this blank area. 29 3/4 (756) 32 1/2 (826) 34 7/8 (886) 37 1/8 (943)
30 The armature and electromagnet cannot be aligned. 27 3/4 (705) 30 5/8 (778) 33 (838) 35 3/8 (899)
32 31 3/8 (797) 33 7/8 (860)
X =
Di
m
ensi
on of
d
oor
ja
m
b
t
o
wal
l
Y = Dimension of door width