STI 1210D - Manuel

Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
INSTALLATION OF STI-1210D SPEAKER HORN/STROBE DAMAGE STOPPER®
All specifications and information shown were current as of publication and are subject to change without notice.
INSTALLATION NOTES
1. To minimize strobe light loss, regardless of the type of horn/strobe appliance
used, the clear section (not the section containing the cutout slots) must be
centered over the strobe light lens. Failure to follow these instruction may
lead to light loss transmission.
2. Damage Stopper must be installed to comply with applicable NEC, NFPA and
local codes.
3. In applications where wash downs, rainfall or condensation occur, it is
recommended that a drain or weep hole be provided. Refer to weep hole
installation diagram.
4. Damage Stopper may be installed outdoors when appliance carries an
outdoor rating.
Electronic warranty form at www.sti-usa.com/wc14
1210DIS APRIL2006
CLEANING INSTRUCTIONS
Rinse with water to remove abrasive dust and dirt. Wash with
soap or mild detergent, using a soft cloth (do not scrub). Rinse
once more then dry with a soft cloth or chamois. To remove
grease or wet paint, rub gently with a cloth wetted with
naphtha. Then wash and rinse. DO NOT USE RAZOR BLADES.
INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW
1. Using back box assembly as a template, place against mounting surface at proper location according to NFPA 72.
2. Mark and drill (4) holes 1/4 in. (6.3mm) diameter, 1 1/4 in. (32mm) deep.
3. If conduit is present, select the proper inserts and slide them into the back box notch.
4. Insert the (4) anchors into the wall.
5. Mount back box to wall with screws.
6. Install electrical fittings as needed.
7. Install horn/strobe appliance.
8. Install cover with clips and screws.
9. Test appliance according to appliance manufacturer’s instructions.
1
2
B
C
D
F
E
G
HORIZONTAL CENTERLINE
OF ENCLOSURE
CENTERLINE
MOUNTING BOSS
FOR BACKBOX MOUNTING
HEIGHT 80 in.
FRONT VIEW OF ENCLOSURE
A 1-1/16 in. DIAMETER CONDUIT
ENTRY HOLE MUST BE FIELD INSTALLED
CENTER LINE
TOP VIEW
1-3/4
TOP VIEW
A 1-1/16 in.
DIAMETER CONDUIT
ENTRY HOLE MUST
BE FIELD INSTALLED
CENTER LINE
1-3/4
#8-32 x 3/8 in.
MACHINE SCREWS
(NOT INCLUDED)
DRILL FOR CONDUIT ENTRY
CLEAR
SECTION
HEIGHT
7.75 in.(197mm)
WIDTH
5.25 in.(133mm)
DEPTH
6.5 in.(165mm)
629764 RETAINING CLIPS
(4) PROVIDED
629761 NEOPRENE GASKET
629762
DRAIN
SCREEN
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
A
06297T MOUNTING
TABS (4) PROVIDED
!
06297A BACKBOX
NEOPRENE GASKET
3 3/8 in.
(86mm)
3/4 in.(44mm)
629763 STANDOFF BLOCKS
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREWS
(4) PROVIDED
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
PRODUCT DIMENSIONS
HEIGHT
8.5 in.(216mm)
DEPTH
5.57 in.(146mm)
WIDTH
6.5 in.(165mm)
1
2
INSTALL CLAMP IN 2nd. NOTCH AS SHOWN
LOCATED IN THIS AREA
DRILL A .25 in.(6.3mm) DIA. HOLE
APPROX
CENTER LINE
OF UNDERSIDE OF
COVER
1 in.(25mm)
19033 ANCHOR
(4) PROVIDED
EXISTING
FLUSH MOUNT
HORN/STROBE
APPLIANCE
629764 CLAMP
(4) PROVIDED
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
CLEAR
SECTION
SURFACE MOUNTED
CONDUIT INSERTS
(USE WHERE NEEDED)
ONE OF EACH PROVIDED
!
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS ORDER SUB-121
ENVIRO KIT
19047 #8-32 x 3/8 in.
SOCKET HEAD CAP SCREW
(4) PROVIDED
06297D BACKBOX
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
HEIGHT
7.75 in.(197mm)
DEPTH
4.75 in.(120mm)
WIDTH
5.25 in.(133mm)
CLEAR
SECTION
!
629764 CLAMP
(4) PROVIDED
APPROX
CENTER LINE
OF UNDERSIDE OF
COVER
1 in.(25mm)
19033 ANCHOR
(4) PROVIDED
EXISTING
HORN/STROBE
APPLIANCE
OPTIONAL CONDUIT HUB
SUB-6297B20
(ACCEPTS 3/4 in. RIGID
CONDUIT FITTINGS)
INCLUDES GASKET AND
MOUNTING HARDWARE
LOCATED IN THIS AREA
DRILL A 1/4 in.(6.3mm) DIA. HOLE
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS OREDER SUB-122
ENVIRO KIT
06297T EXTERNAL
MOUNTING TABS —
INSERT TABS INTO
FRAME SLOTS AS SHOWN
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREW (4) PROVIDED
06297C FRAME ASSY.
PRODUCT DIMENSIONS
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
PRODUCT DIMENSIONS
HEIGHT
8.5 in.(216mm)
DEPTH
5.57 in.(146mm)
WIDTH
6.5 in.(165mm)
1
2
INSTALL CLAMP IN 2nd. NOTCH AS SHOWN
LOCATED IN THIS AREA
DRILL A .25 in.(6.3mm) DIA. HOLE
APPROX
CENTER LINE
OF UNDERSIDE OF
COVER
1 in.(25mm)
19033 ANCHOR
(4) PROVIDED
EXISTING
FLUSH MOUNT
HORN/STROBE
APPLIANCE
629764 CLAMP
(4) PROVIDED
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
CLEAR
SECTION
SURFACE MOUNTED
CONDUIT INSERTS
(USE WHERE NEEDED)
ONE OF EACH PROVIDED
!
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS ORDER SUB-121
ENVIRO KIT
19047 #8-32 x 3/8 in.
SOCKET HEAD CAP SCREW
(4) PROVIDED
06297D BACKBOX
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
WEEP HOLE INSTALLATION
INSTALL CLAMP IN NOTCH 2 AS SHOWN
INTERNAL DIMENSIONS
REMARQUES SUR L’INSTALLATION
1. Afin de minimiser la perte de lumière stroboscopique, quel que soit le type d’alarme sonore/de stroboscope utilisé, la section dégagée (et NON la
section contenant les fentes de découpe), doit être centrée sur l’objectif stroboscopique. Le fait d’omettre ces instructions risque d’entraîner la perte
de diffusion de la lumière.
2. Le Stopper de dégâts doit être installé de sorte à être conforme avec les normes NEC, NFPA applicables et les codes locaux.
3. Dans les applications où des jets d’eau, des précipitations ou de la condensation se produisent, il est recommandé de prévoir un trou de vidange ou
une barbacane. Reportez-vous à schéma d’installation d’une barbacane.
4. Il est possible d’installer un Stopper de dégâts à l’extérieur lorsque l’appareil est homologué pour utilisation à l’extérieur.