Swiss+Tech BodyGard Tire Safety Tool 6-in-1 - Manuel

Patents pending. Made in China. BODYGARD ® is a
registered trademark and MMMMMMMMI ™ and MI ™
are trademarks of Swiss +Tech Products. Specifications
are subject to change without notice.
©2011 Swiss+Tech Products, Solon, OH
44139 USA
BodyGard ®
Tire Safety Tool
6-in-1
www.swisstechtools.com
800-414-8799
ST74082
This product contains button batteries.
IF SWALLOWED, batteries could cause
severe injury or death in just 2 hours.
SEEK MEDICAL ATTENTION IMMEDIATELY.
• DO NOT dispose of batteries in fire,
batteries may explode or leak.
• DO NOT mix old and new batteries.
• DO NOT mix alkaline, standard
(carbon-zinc) or rechargeable
(nickel-cadmium) batteries.
• REMOVE BATTERIES from equipment
which is not to be used for an extended
period of time.
BATTERY WARNINGS:
Limited LIFETIME Warranty
This product is c overed by a Limited Lifetime Warranty
to the original purchaser in that this product is free from
defects in workmanship and ma terials. During the
warranty period, this product will either be repaired or
replaced with a product of equal or greater value,
excluding any custom engraving or printing.
Damage through normal wear and tear (including
battery expiration and surface coatings), repair or
alteration, misuse, abuse, neglect, accident, improper
storage and handling, fire, negligence, improper
cleaning, circumstances not directly attributable to
manufacturing defects, or act of God is not included.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO, IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR USE.
This warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state. Simply return your SWISS +TECH ® brand product
postpaid and insured to:
Swiss+Tech Products
30725 Solon Industrial Pkwy
Solon, OH 44139 USA
• Press Tire Pressure Gauge button (B) to activate
PSI readout mode, press again to change to
BAR readout mode.
• Push Pressure Gauge Socket (1) onto tire valve stem
until no hissing sound of escaping air is heard.
• Hold Gauge on valve stem for about 3 seconds until
the pressure reading displayed is stable.
• To turn off Pressure Gauge, press and hold button for
3 seconds, or wait 10 seconds for automatic shutoff.
3. LED FLASHLIGHT
• Locate the button with the “lamp symbol” (A)
on the front of your Tire Safety Tool.
• Press 1 time to turn on flashlight.
• Press 1 time again to turn off.
4. HANDY BOTTLE OPENER
5. FLAT SCREWDRIVER
• Torque gently, not designed for heavy-duty use.
6. KEY RING QUICK RELEASE
• Slide Quick Release button to easily add or
remove the tool from your Key Ring.
REPLACING THE BATTERY
• Using a small Phillips head screwdriver, loosen the
captive screw (screw stays in battery cover) on the
back of your BodyGard ® Tire Safety Tool .
• Open the battery compartment.
• Remove the old battery and replace with a new
CR2032 3V lithium battery.
• Replace the battery cover and tighten the screw
gently. Be sure not to over tighten.
The Handy Way To Ensure:
• Proper Inflation
• Safety
• Fuel Economy
Carry your Tire Safety Tool on
your key ring so it’s always
with you when you need it!
• Stainless Steel Components – long lasting!
• Tough ABS Construction for rugged use.
• Open and fully
extend the
Tread Depth Tool
(which is also the
bottle opener
and screwdriver).
• Insert the tip into
the deepest tread
on your tire to see
what color is visible.
• Repeat at various
locations on both
inner and outer
grooves and at
additional locations
around the circumference of the tire. This will
tell you if the tire is wearing unevenly.
• GREEN means the tread depth is fine.
• YELLOW means you will need new tires soon.
• RED means you need new tires.
NOTE: Incorrect air pressure, poor wheel alignment,
worn parts, etc., can cause rapid or uneven tire wear.
Check for wear patterns often to detect problems
before excessive or irregular tread wear ruins the tire.
1. TIRE PRESSURE GAUGE 2. TREAD DEPTH GAUGE
CR2032 3V
Lithium Battery,
Positive Side (+) Up
1
4
A
3
6
5
2
B
QUICK RELEASE:
Slide Quick Release button (6) to easily add
or remove the tool from your Key Ring.
BEFORE USING, REMOVE PULL
TAB TO ACTIVATE BATTERY.
Firmly grasp Pull Tab extending out of the
Battery Door and pull completely out of unit.
Your Tire Safety Tool is now operational.