Sunlite ST40Y48M10X6- - Manuel

M odel M ax I nput V oltage (V dc ) M ax c urrent (a) M ax W attage
ST40 48 3.5 66
Important Safety InStructIonS - Save theSe InStructIonS
uSe only wIth claSS 2 power unIt
• These products are only suitable for connection to a Class 2 power source
and have not been evaluated for use when connected to a power source
that does not comply with Class 2 voltage and energy limited supplies.
cautIon - to prevent the rISk of fIre, do not InStall In
a compartment Smaller than 10 IncheS by 10 IncheS by
(xx+12) IncheS (where xx IS the length of the lumInaIre In
IncheS)
all InStallatIonS of SunStrIp40 Should be
performed by a certIfIed electrIcIan and be In
complIance wIth the natIonal electrIcIanS code aS well
aS local codeS.
SuItable for wet locatIonS
E338721
F
ixture
W
iring
:
Solid State led
St40
Strip light
traditional
Surface Mount
C
ertiFiCation
:
UL and cUL
Damp/Wet Location Listed
IP64/IP66 Rated
e
nergy
:
>0.9 Power Factor
700-1400mA / ~ 48VDC
-30° C to 40°C
C
ontaCt
:
4811 Quail Crest Place
Lawrence, KS 66049
www.sunlitest.com
T:785.856.0219
F
ixture
i
nStallation
i
nStruCtionS
:
Cut or drill a 1-1/8”
hole in ceiling.
Retrieve wires in ceiling
and outfit with bullet
connections.
• Side of wire closer to
LED driver should be
fitted with a female
bullet connector.
• Side of the wire
farther from the LED
driver should be fitted
with a male bullet
connector.
Screw in
mounting bracket
over hole.
SunStrip40 - “St40-” - low voltage claSS 2 led luMinaire
Suggested wiring utilizes bullet connections in alignment with the direction of current flow from the driver.
Thread fixture wire
through ceiling
mount. Outfit fixture
wire with bullet
connections.
• Core (+) with a
male bullet
connector.
• Shield (-) with
a female bullet
connector.
Push wires into
ceiling. Screw in
#8 screws into
mount base to
connect the base
to bracket.
1 2 3
4 5
Connect bullet
connections from
light fixture and
from ceiling wires
together.
6
turn power off before any inStallation, inSpection or reMoval of fixture/wiring.
Strip Driver
W (-)
W (+)
B (-)
R (+)
Side with clip is positive.
conSigneS de SÉcuritÉ iMportanteS - conServeZ SoigneuSeMent ceS inStructionS
a utiliSer uniQueMent avec une Source d’aliMentation de
claSSe 2
• Ces produits doivent être branchés uniquement à une source d’alimen-
tation de classe 2 et n’ont pas été testés pour une utilisation lors d’une
connexion à une source d’énergie non conforme à la tension de classe 2
et à l’approvisionnement en énergie limitées.
attention - pour Éviter leS riSQueS d’incendie, ne paS
inStaller danS un coMpartiMent inferieur a 10 pouceS
Sur 10 pouceS Sur (xx+12) pouceS (oÙ xx eSt la longueur
du luMinaire en pouceS).
ce produit doit Étre inStallÉ Selon le code
d’inStallation pertinent, par une perSonne Qui connaÍt
bien le produit et Son fonctionneMent ainSi Que leS
riSQueS inhÉrentS.
convient aux eMplaceMentS MouillÉS.