Sunlite SR50M1X6-RC - Manuel

M odel M ax I nput V oltage (V dc ) M ax c urrent ( M a) M ax W attage
SR50 / SR50-EB / SR50-RC 30 700 7.8
Important Safety InStructIonS - Save theSe InStructIonS
uSe only wIth claSS 2 power unIt
• These products are only suitable for connection to a Class 2 power source
and have not been evaluated for use when connected to a power source
that does not comply with Class 2 voltage and energy limited supplies.
all InStallatIonS of SunStar50 Should be
performed by a certIfIed electrIcIan and be In
complIance wIth the natIonal electrIcIanS code aS well
aS local codeS.
SuItable for damp locatIonS
conSIGneS de SÉcurItÉ ImportanteS - conServeZ SoIGneuSement ceS InStructIonS
a utIlISer unIQuement avec une Source d’alImentatIon de
claSSe 2
• Ces produits doivent être branchés uniquement à une source
d’alimentation de classe 2 et n’ont pas été testés pour une utilisation lors
d’une connexion à une source d’énergie non conforme à la tension de
classe 2 et à l’approvisionnement en énergie limitées.
ce produIt doIt Étre InStallÉ Selon le code
d’InStallatIon pertInent, par une perSonne QuI connaÍt
bIen le produIt et Son fonctIonnement aInSI Que leS
rISQueS InhÉrentS.
convIent auX emplacementS humIdeS.
E338721
F
ixture
W
iring
:
Solid State led
Sr50
Sr50-eB
Sr50-rC
Can light /
down light
C
ertiFiCation
:
UL and cUL
Damp Location Listed
IP64 Rated
e
nergy
:
>0.9 Power Factor
700mA / ~ 10VDC
-30° C to 40°C
C
ontaCt
:
4811 Quail Crest Place
Lawrence, KS 66049
www.sunlitest.com
T:785.856.0219
F
ixture
i
nStallation
i
nStruCtionS
:
For soft material
ceilings (drop-in),
cut or drill a 2” hole.
For hard material
ceilings (wood,
drywall, etc.), cut or
drill a 2 1/16” to 2
1/8” hole.
Insert mounting
bracket into hole.
Retrieve wires in
ceiling and outfit
with bullet
connections.
SunStar50 - “Sr50-” - led type-iC reCeSSed Ceiling mount luminaire
Suggested wiring utilizes bullet connections in alignment with the direction of current flow from the driver.
Outfit light fixture
with bullet
connections
• Red (+) with a
female bullet
connector
• Black (-) with
a male bullet
connector
Push wires back
into ceiling.
Push fixture
into bracket
until flush with
ceiling.
1 2 3
4 5
Connect bullet
connections from
light fixture and
from ceiling wires
together.
6
turn power off before any inStallation, inSpeCtion or removal of fixture/wiring.
piCtured below iS the inStallation of the Sr50 Can light. the Sr50-eb and Sr50-rC are inStalled the Same way.
R(+) R(+)
R(+) B(-)
T o P ower S uPPly T o S erieS
F ixTure
r(+) r(+)
r(+) B(-)
R(+) R(+)
Sr50 Sr50
r(+) B(-) r(+) B(-)
T o P ower S uPPly
Sr50 Sr50
r(+) B(-) r(+) B(-)