GE GTUP240EMWW - Manuel (Page 4)

Installation Instructions
4
Minimum Clearance Other Than Alcove or Closet Installation
0LQLPXPFOHDUDQFHWRFRPEXVWLEOHVXUIDFHVDQGIRUDLURSHQLQJDUH LQFOHDUDQFHERWKVLGHVDQGUHDU&RQVLGHUDWLRQmust
be given to provide adequate clearance for installation and service.
1 PREPARING FOR INSTALLATION
OF NEW APPLIANCE
REMOVING LINT FROM WALL EXHAUST
OPENING
• Remove and discard existing plastic or metal foil
transition duct and replace with UL listed transition duct.
2 ELECTRICAL CONNECTION INFORMATION
WARNING -
TO REDUCE THE RISK OF
FIRE, ELECTRICAL SHOCK AND PERSONAL INJURY:
• DO NOT USE AN EXTENSION CORD OR AN
ADAPTER PLUG WITH THIS APPLIANCE.
This dryer must be electrically grounded in accordance
with local codes, or in the absence of local codes, with the
National Electrical Code, ANSI/NFPA NO. 70 or Canadian
Electrical Code, CSA C22.1.
INTERNAL DUCT
OPENING
CHECK THAT EXHAUST
HOOD DAMPER OPENS
AND CLOSES FREELY.
WALL
ELECTRICAL REQUIREMENTS
This appliance must be connected to an individual
EUDQFK FLUFXLW SURWHFWHG E\ WKH UHTXLUHG WLPHGHOD\
IXVHV RU FLUFXLW EUHDNHUV $ IRXU RU WKUHHZLUH VLQJOH
SKDVH 9 RU 9 +]  DPS FLUFXLW
is required. If the electric supply does not meet the
DERYH VSHFL¿FDWLRQV WKHQ FDOO D OLFHQVHG HOHFWULFLDQ
GROUNDING INSTRUCTIONS
A. )RUDJURXQGHGFRUGFRQQHFWHGDSSOLDQFH
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of
least resistance of electric current. This appliance is
HTXLSSHGZLWKDFRUGKDYLQJDQHTXLSPHQWJURXQGLQJ
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
WARNING -
Improper connection of the
equipment-grounding conductor can result in a risk
RI HOHFWULF VKRFN &KHFN ZLWK D TXDOL¿HG  HOHFWULFLDQ
or serviceman if you are in doubt as to whether the
appliance is properly grounded.
TILT THE APPLIANCE
SIDEWAYS AND REMOVE
THE FOAM SHIPPING PADS
%<38//,1*$77+(6,'(6
$1'%5($.,1*7+(0
AWAY FROM THE APPLIANCE
/(*6%(685(725(029(
ALL OF THE FOAM PIECES
AROUND THE LEGS.
NEW HOME OR REMODELING FAUCETS/
DRAIN STANDPIPE/ELECTRICAL LOCATION
FLOOR
µ
42”
12”
Locate spigots,
drain standpipe
and electrical plug
in this area
Right side of
Laundry Center.
6W\URIRDP%ORFN
Washer hoses
and parts
After the machine is in the
home, remove remaining
packing material/carton from
washer.
DO NOT REMOVE SHIPPING
ROD AT THIS TIME.
Remove styrofoam block.
Remove the bag containing
the Washer hoses and parts
parts from tub. Put styrofoam
block back in tub opening to
hold tub in place during the
rest of installation.
0RYH ZDVKHU FORVH WR ¿QDO
position. Make sure there is
at least a 24” clearance on
right side of washer to remove
shipping bar. PULL SHIPPING
%$5 287 86,1* <(//2:
PLASTIC HANDLE. Keep bar so
it can be reinstalled if washer
is ever moved again.
Shipping
%DU
Yellow plastic handle