Hitachi DV-PF35U - Manuel (Page 7)

Setup
– 7 – EN
English
Select this connection when you want to view or record a
scrambled channel. With this connection, channels cannot be
changed on the VCR/DVD. You can view or record ONLY the
channels you have selected on the cable box or the satellite
box.
• While you are recording, only the recorded channel can be
viewed.
To select channels of the cable box or satellite box
1) Turn on the VCR/DVD by pressing y
y /I, and then, press
VCR/TV.The “POWER” and “VCR” lights on the front panel
will appear. Then, press SKIP/CH (i/K or j/L) to
select channel 3 or 4 (the same channel as the output
channel of the cable box or satellite box).
• If you use the channel 4, you need to change the
VCR/DVD’s RF output to channel 4. Refer to “RF Output
Channel”.
2) At the TV, select channel 3 or 4 (the same channel as you
have selected at step 1).
3) At the cable box or satellite box, select the channel you
want to view or record.
Select this connection when you want to change channels on
the VCR/DVD. With this connection, you may watch one chan-
nel while recording another.
• You may not view or record a scrambled channel.
To select channels of the cable box or satellite box
1) At the cable box or satellite box, select channel 3 or 4 (the
same channel as the VCR/DVD’s RF output channel).
• Refer to “RF Output Channel”.
2) At the TV, select the same channel as the output channel
(3 or 4) of the cable box or satellite box.
3) Turn on the VCR/DVD by pressing y y /I, and then, press
VCR/TV. The “POWER” and “VCR” lights on the front panel
will appear. Then, select the channel you want to view or
record.
To playback a tape
Follow the steps 1) to 2) above. Then, playback a tape.
• Refer to “Playback” on page 13.
To view one channel while recording another
1) While you are recording on the VCR/DVD, press VCR/TV
so that the “VCR” light disappears on the VCR/DVD.
2) At the cable box, select the channel you want to view.
ANT-OUT
ANT-IN
(Back of VCR/DVD)
IN OUT
(Back of TV)
Cable
Signal
Connection A
(Cable box or
Satellite box)
RF cable
(supplied)
ANT-OUT
ANT-IN
RF cable (supplied) RF cable
(Back of TV)
IN OUT
(Cable box)
Cable
Signal
Connection B (Back of VCR/DVD)
Hint for Cable Box or Satellite Box
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press OUTPUT on the VCR/DVD so that the VCR OUTPUT light is lit.
• If “VCR” light does not appear on the display of this unit, press VCR/TV on the remote control.
4) Press PLAY B once.
5) After a few seconds, press PLAY B on the VCR/DVD for 3 seconds.
• The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.
In this case, “ch04” will appears on the front panel.
• When a picture does not appear on the TV screen, repeat step 4.
6) Press STOP C to stop playback.
RF Output Channel
Connections
Please refer to “Basic TV Connection” on the front page before you use this unit.
Hint Hint
• The RF output channel
may not change when
you adjust tracking dur-
ing playback. In this
case, stop the playback,
and start the playback
again. After that, press
PLAY B on the
VCR/DVD for 3 seconds
again.
H9850UD_EN/SP.qx3 05.4.8 11:42 AM Page 7