Blue Rhino GBC956W1NG-C - Manuel (Page 9)

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
page no.
9
Operating Instructions
Checking for Leaks
Burner Connections
1. Make sure the natural gas line is securely fastened
to the burner and the main gas natural gas line.
If your unit was assembled for you, visually check
the connection between the burner venturi pipe and
orifice. Make sure the burner venturi pipe fits over
the orifice.
WARNING: Failure to inspect this
connection or follow these instructions
could cause a fire or an explosion
which can cause death, serious bodily
injury, or damage to property.
2. Please refer to diagram for proper installation.
(Figure 1 and 2)
3. If the burner pipe does not rest flush to the orifice,
please contact 1.800.762.1142 for assistance.
Gas Line Connection
1. Make 2-3 oz. of leak solution by mixing one part
liquid dishwashing soap with three parts water.
2. Make sure control knobs are “OFF”. (Figure 3)
3. Turn “ON” natural gas main valve.
4. Spoon leak check solution at all “X” locations
(Figure 4)
a. If any bubbles appear turn natural gas line valve
to “CLOSED”, reconnect and re-test.
b. If you continue to see bubbles after several
attempts, turn natural gas line valve to “CLOSED”
and disconnect natural gas line and contact
1.800.762.1142 for assistance.
c. If no bubbles appear after one minute turn natural
gas line valve to “CLOSED”, wipe away solution
and proceed.
Operating Main Burners
First Use
1. Make sure all labels, packaging and protective films
have been removed from the grill.
2. Remove manufacturing oils before cooking on this
grill for the first time by operating the grill for at
least 15 minutes on “HIGH” with the lid closed. This
will “heat clean” the internal parts and dissipate
odors.
Lighting
1. Open lid. Attempting to light the burner with the
lid closed may cause an explosion!
2. Make sure there are no obstructions of airflow to
the burners. Spiders and insects can nest within
and clog the burner / venturi tube at the orifice. A
clogged burner tube can lead to a fire beneath the
appliance.
3. All control knobs must be in the “OFF” position.
(Figure 3)
4. Turn natural gas line valve to “OPEN”.
5. Select burner to light. Push and turn control knob
counterclockwise to “HIGH”.
6. Press the electronic igniter button and hold for 5
seconds to light burner.
7. If ignition does not occur in 5 seconds, turn burner
control knob “OFF”, wait 5 minutes, and repeat
lighting procedure.
8. If igniter does not light burner, use a lit match
secured with the lighting rod provided to light
burners manually. Access the burners through the
cooking grid and heat plates. Position the lit match
near side of the burner. (Figure 5)
Important: Always use the lighting rod provided when
lighting burners with a match.
9. After lighting, observe the burner flame, make sure
all burner ports are lit and flame height matches
illustration. (Figure 6)
Note: Each burner lights independently - repeat steps
5-9 for the other burners.
Figure 1
Burner
venturi pipe Valve Soft Pipe
Connection
Gas Valve
with Orifice
Main Burners
Figure 2
Gas
Connection Gas Valve with
Orifice
Valve
Soft Pipe
Connection
Side Burner
Burner
venturi
pipe
Figure 3
Figure 4
Figure 5
Figure 6
Burner
Flame
Slight
Yellow
Slight
Blue
Dark
Blue
Installing Natural Gas Line
Installation should be done by a qualified service person.
CAUTION: If young children are in the area, a locking valve should be
considered.
Connect Natural Gas Line
Before connecting, be sure that there is no debris caught in
the head of the natural gas line, head of the grill natural gas
line or in the head of the burner and burner ports.
Connect grill natural gas line to natural gas line.
Disconnect Natural Gas Line
Before disconnecting make sure the natural gas line valve is “OFF”.
Disconnect grill natural gas line from natural gas line.