Pfister GT34-3TSS - Manuel (Page 3)

3 HOLE INSTALLATION NO SIDE SPRAY
5 INSTALLING DECKPLATE
Ensure that the Plastic Putty Plate (
5A) is pressed on the Deckplate (5B). Place
a bead of plumber’s putty in the groove along the outer edge of the Putty Plate
(
5A). Install the Deckplate (5B) over the three holes in your sink.
6 SECURING DECKPLATE TO DECK
)URP XQGHUQHDWK VLQN KDQG WLJKWHQ :LQJ 1XWV
6A) to Mounting Posts (6C).
Caution: do not over-tighten wing nuts. Remove any excess putty from
around the outside edge of Deck Plate (
6B).
Go To Step 17 STOP
3 HOLE INSTALLATION WITH SIDE SPRAY
7 INSTALLING DECKPLATE
Ensure that the Plastic Putty Plate (
7A) is pressed on the Deckplate (7B). Place
a bead of plumber’s putty in the groove along the outer edge of the Putty Plate
(
7A). Install the Deckplate (7B) over the three holes in your sink.
8 SECURING DECKPLATE & HOSE GUIDE
Insert Hose Guide (
8A) into the side hole in the Deckplate (8B) and onto the
sink hole. Align the hose guide Tabs (
8C) to those in the Deckplate Hole (8D).
)URP XQGHUQHDWK VLQN VHFXUH WKH +RVH *XLGH
8A) by screwing the Plastic
Locknut (
8D  6HFXUH 'HFNSODWH 8E) by screwing Wing Nut (8F) to Mounting
Post ( 8G). Hand tighten. Caution: do not over-tighten. Remove any excess
putty from around the outside edge of Deckplate ( 8E).
9 SIDE SPRAY INSTALLATION
,QVHUW WKH 6LGH 6SUD\ +RVH
9A) through the Hose Guide (9B  )URP XQGHUQHDWK
VLQN IHHG WKH 6LGH 6SUD\ +RVH 9A) back up through the center hole of sink
and through Deckplate ( 9C) so that it is above the sink.
Go To Step 16 STOP
2 HOLE INSTALLATION
(For T34-4T Models Only)
10 INSTALLING MOUNTING RING & GUIDE FLANGE
Place Mounting Ring (
10A) over Plastic Gasket (10B) and sink hole. If desired,
SODFH D VPDOO EHDG RI SOXPEHU¶V SXWW\ WR WKH XQGHUVLGH RI WKH +RVH *XLGH )ODQJH
(
10C). Align both Mounting Ring (10A DQG +RVH *XLGH )ODQJH 10C) to the
center of sink holes.
11 SECURING HOSE GUIDE
Insert Hose Guide (
11A LQWR +RVH *XLGH )ODQJH 11B) and onto the sink hole.
)URP XQGHUQHDWK VLQN VHFXUH WKH +RVH *XLGH 11A) by screwing the Plastic
Locknut ( 11C). Hand tighten.
5
6
7
8
9
10
11

(1*/,6+
%27720 *5229(
5B
6B
7A
%27720 *5229(
5A
6A
6A
7B
)
8E
8D
8G
8A
8C
8B
8B
8D
8A
6C 6C
9A
9B
9C
10A
10B
10C
11A
11B
11C