GeneralAire 900 SERIES Elite - Manuel (Page 3)

PARTS LIST FOR HUMIDIFIER
AT
OUTSIDE
TEMPERATURE
RECOMMENDED
SETTING
-20°F -29°C 15%
-10°F -23°C 20%
0°F -18°C 25%
+10°F -12°C
+20°F - 7°C
30%
35%
+30°F - 1°C 40%
Your humidifier is engineered to give helpful and trouble-free humidification. For maximum efficiency the following cleaning procedures should be
carried out at the end of each heating season:
1. Turn off water supply and electrical power to humidifier.
2. Remove cover, distributor trough, evaporator pad and drain pan. Clean excessive mineral deposits from the distributor
trough, drain pan, pad rails, and humidifier cabinet. A solution of 1/2 vinegar & 1/2 water will help loosen mineral deposits.
3. Replace humidifier evaporator pad if necessary. (Part number GA19) Install trough and drain pan.
Replace cover. Replace evaporator pad yearly for peak performance.
4. In heavy mineral areas or if the solenoid valve fails to function disconnect the 1/4” water supply line from the solenoid valve.
Carefully pull the strainer screen (P.N. GA4004) from the valve body (P.N. 900-6). Clean the mineral deposits from all
parts.
If the orifice is clogged, it may be opened by inserting a small pin. Reinsert the filter into the orifice fitting and screw the
brass strainer body into the solenoid valve.
5. Reconnect the 1/4” water line to the solenoid valve if necessary. Turn on the water supply and check all points for leakage.
The operation of the unit may be checked by starting the furnace. The humidifier operates only when the furnace blower is
running or the burner circuit is energized. The humidifier is now ready for operation.
6. During the summer, turn off water supply and electrical power to humidifier. Close air damper.
CARE AND MAINTENANCE
LIMITED WARRANTY
This humidifier, if properly registered by the return of the warranty registration card to the manufacturer, is warranted to the consumer against defects in
materials and workmanship for a period of ten years from the date of installation. Evaporator pads, water strainers or metering orifices are not covered by this
limited warranty or any other warranties. Any other defective parts will be repaired without charge except for removal, reinstallation and transportation costs. To
obtain repair service under this limited warranty, the consumer must send the defective part or the complete humidifier to the manufacturer.
THERE ARE NO EXPRESS WARRANTIES COVERING THIS HUMIDIFIER OTHER THAN AS SET FORTH ABOVE, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED. THE MANUFACTURER ASSUMES NO LIABILITY IN
CONNECTION WITH THE INSTALLATION OR USE OF THIS PRODUCT, EXCEPT AS STATED IN THIS LIMITED WARRANTY. THE MANUFACTURER WILL
IN NO EVENT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow either
limitations on implied warranties, or exclusions from incidental or consequential damages, so the above exclusion and limitation may not apply to you.
Any questions pertaining to this limited warranty should be addressed to the manufacturer. (U.S.A.: The manufacturer has elected not to make available the
informal dispute settlement mechanism which is specified in the Magnuson-Moss Warranty Act.)
900-14 DRAIN PAN
900-11 DAMPER KNOB
900-28 DAMPER DISK
900-2 SIDE PANEL DISCHARGE
900-40 PAD RAIL
GA-19 EVAPORATOR PAD
900-15 DISTRIBUTOR TROUGH
900-13 COVER
GA4231 YELLOW ORIFICE
P102 COMPRESSION SLEEVE (BRASS)/P190 COMPRESSION SLEEVE (PLASTIC)
P101 COMPRESSION NUT
900-1 CHASSIS
900-9 NOZZLE
900-10 SPOUT
GA4040 SOLENOID VALVE ASM
GA4004 STAINER SCREEN
P102 COMPRESSION SLEEVE
P101 COMPRESSION NUT
GA4266 DISTRIBUTOR TUBE
P189 BRASS TUBE INSERT
747-38 TUBING KIT (AVAILABLE)
900-71 NAMEPLATE