Listening through a receiver, Check points before requesting service – Samsung PS50A467P1M Manuel d'utilisation
Page 47
English - 47
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1 Press
the
TOOLS button.
Press the ▲ or ▼ button to select Receiver, then press the ENTER
button.
2
Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
3 Press
the
EXIT button to exit.
®
output from the TV’s Optical jack. When the TV is displaying a DTV(air)
signal, the TV will send out 5.1 channel sound to the Home theater
receiver. When the source is a digital component such as a DVD and is
connected to the TV via HDMI, only 2
channel sound will be heard from the Home Theater receiver.
®
®
Out jack of the TV.
®
power failure), the TV Speaker may be set to Off when you turn the TV on again.
Check Points before Requesting Service
Symptom
Solution
Anynet+ does not work.
■ Check if the device is an Anynet+ device. The Anynet+ system supports
Anynet+ devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI cable connections.
■ Check whether
Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI cable, please make sure to search
devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+.
■ Check if the Anynet+ device is properly connected to the TV and check if the
Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then press the
TOOLS button to show the Anynet+ menu and select a menu you want.
I want to exit Anynet+.
■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a device
other than Anynet+ devices.
■ Press any of CH, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a tuner-
embedded Anynet+ device is not connected.)
The message Connecting to
Anynet+ device… appears on the
screen.
■ You cannot use the remote control when you are configuring Anynet+ or
switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to view mode is
complete.
The Anynet+ device does not play.
■ You cannot use the play function when Plug & Play is in progress.
The connected device is not
displayed.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI cable is properly connected.
■ Check whether
Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Search
Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI cable only. Some HDMI
cables may not support Anynet+ functions.
The TV programme cannot be
recorded.
■ Check whether the antenna jack on the recording device is properly
connected.
The TV sound is not output
through the receiver.
■ Connect the optical cable between TV and the receiver.
Tools
Move
Enter
View TV
Device List
Recording : DVD
DVD Menu
DVD Menu
Picture Mode
: Dynamic
Sound Mode
: Standard
Sleep Timer
: Off
▼
Exit
w Ow[\WPiu]_TWX\[^hUGGG[^
YWW_TW\TX\GGG㝘䟸GZaYXaWW